Blog

Downlights in insulated ceilings: what’s safe and what isn’t

· 3 min read · Fins Up Electrical, licence 91921

5.0 on GoogleLicence 91921Open 24 hours, Mon to SatFree quotes

Insulation can only sit over a downlight if the fitting is rated for it, which is what IC-rated means. Old halogen downlights and their transformers run hot and must not be covered, and insulation on or too close to them is a common cause of roof fires. If your ceiling has halogens and insulation, get it checked and consider swapping to IC-rated LED fittings.

What does IC-rated mean on a downlight?

IC stands for insulation contact. Recessed light fittings in Australia are classified under the standard AS/NZS 60598.2.2 by how they behave when insulation is near them. An IC-rated fitting is designed so building insulation can touch it and cover it without it overheating.

Fittings without that rating need a clear space around them, or a guard, so insulation stays back. The marking is on the fitting or its box. If you can’t find a rating on an old fitting, treat it as one that must not be covered.

Why are old halogen downlights a fire risk?

Halogen globes get very hot, and so can the transformers that power them. Push insulation hard against them and the heat has nowhere to go. Over time the insulation, dust or nearby timber can scorch, smoulder or catch.

Fire services name insulation on or too close to halogen downlights as one of the more common causes of roof fires. The Electrical Safety Office’s roof space advice tells Queenslanders to check insulation isn’t covering electrical fittings, especially downlights.

How does insulation end up over the lights?

A few ways:

  • New insulation gets laid over the whole ceiling without anyone moving it back from older fittings.
  • Batts get pushed around by someone working in the roof, like a TV antenna installer or a plumber.
  • Loose-fill insulation drifts over time and settles against fittings.
  • Downlights get added to a ceiling that’s already insulated, and the batts are dropped back on top.

None of it is obvious from inside the house. The light still works. You only see the problem from the roof space.

What should I check in my ceiling?

Don’t go poking around the wiring. The roof space has live cables, and on a home with solar there are DC cables that can be live during the day. The Electrical Safety Office advises making sure your circuits are protected by a safety switch, and testing it before you go up.

What you can safely look for with a torch, from the access hole:

  • Insulation lying over or pressed against any light fitting or transformer.
  • Dark, brown or scorched marks on insulation or timber near a light.
  • A burning smell when the lights have been on a while.

If you see any of that, leave the lights off and call a licensed electrician.

What’s the fix?

Usually the best fix is to replace old halogen fittings with IC-rated LED downlights. LEDs run far cooler and draw much less power, and an IC-rated fitting lets the insulation go back over the top. That closes the gaps that were letting heat into your rooms in summer.

Where an existing fitting stays, it needs the right clearance or an approved guard so insulation can’t creep back. Replacing a fitting is electrical work and has to be done by a licensed electrician in Queensland. See our page on downlight installation for what we fit.

I’m getting new insulation. What should I tell the installer?

Tell them where every downlight, exhaust fan and transformer is. Ask what rating your existing fittings carry and how they’ll keep the right clearance. Better still, have the old halogens swapped to IC-rated LEDs before the insulation goes in, so it can be laid over the top in one go.

Fins Up Electrical can check your downlights, swap them out and leave the ceiling ready for the insulator. Andrew has had 16 years on the tools and quotes free and fixed before any work starts. We cover the Redcliffe peninsula and Moreton Bay. For broader lighting changes, see lighting installation.

Want this sorted? Downlight installation from Fins Up.

Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.

Common questions

Can you put insulation over LED downlights?

Only over fittings rated for it. Check for an IC rating on the fitting or box before covering it.

Are halogen downlights dangerous?

They run hot, and with insulation on or too close to them they’re a known roof fire risk. Swapping them for IC-rated LEDs removes most of that risk.

How do I know if my downlights are IC-rated?

Look for the marking on the fitting or the original packaging. If there’s no rating, treat it as a fitting that must not be covered and have an electrician check it.

Sources

The service