Blog

Replacing halogen downlights with LED

· 3 min read · Fins Up Electrical, licence 91921

5.0 on GoogleLicence 91921Open 24 hours, Mon to SatFree quotes

You can replace halogen downlights with LED either by swapping the globe or by replacing the whole fitting. Swapping globes is cheaper up front, but old transformers often don’t play nicely with LED globes and the old fitting stays in the ceiling. Replacing the fitting with an integrated LED downlight fixes the heat problem, usually lets insulation sit over it, and gives a cleaner result.

Why replace halogen downlights at all?

Three reasons:

  • Power use. Sustainability Victoria puts a 12 volt LED globe at about 75% less energy than a 12 volt halogen globe for the same job. Across a whole house of downlights that adds up.
  • Heat. Halogens run very hot. That heat goes into your ceiling space and your rooms, which is the last thing you want in a Queensland summer.
  • Fire risk. Insulation sitting on or too close to halogen downlights is a known cause of roof fires.

Halogen globes also blow often, so you’re up a ladder more than you’d like.

Can I just swap the halogen globe for an LED globe?

Sometimes. Changing a globe isn’t electrical work, and an LED globe in the same base will often work. The catch is the transformer. Most older halogen downlights run at 12 volts through a transformer sitting in the ceiling. Those transformers were built for the load of a halogen globe. Put a low-draw LED globe on one and you can get flicker, buzzing, or a globe that dies early. Some fittings also use dimmers that don’t suit LED.

The old fitting also stays in the ceiling. Many older halogen fittings aren’t rated to be covered by insulation, so the gap around them stays.

What does replacing the whole fitting involve?

We take out the old halogen fitting and its transformer, and fit a new LED downlight with its own matched driver. In most cases the new light fits the existing hole, or we pick a model with a cut-out that covers it. If the old hole is bigger, there are fittings and trims made for exactly that.

Replacing a light fitting is electrical work, and in Queensland it has to be done by a licensed electrician. The Electrical Safety Office says so plainly: don’t DIY it.

Why does the insulation matter so much?

Insulation should never be left covering an old halogen downlight or its transformer. The Electrical Safety Office tells homeowners to check that insulation isn’t covering electrical fittings in the roof space, especially downlights. Fire services list insulation on or near halogen downlights as one of the common causes of roof fires.

Many LED downlights are IC-rated, which means they’re built to have insulation in contact with them and over them. Swap to an IC-rated fitting and the insulation can go back over the top, closing the gap that was letting heat in.

Which LED downlight should I choose?

  • IC rating. Pick an IC-rated fitting if there’s insulation in your ceiling.
  • Colour. Warm white for living and bedrooms, natural or cool white for kitchens and laundries. Some fittings switch between all three.
  • Dimmable. If you want dimming, the light and the dimmer must suit each other.
  • Cut-out size. Match the existing hole where possible so the ceiling doesn’t need patching.

We bring fittings that suit the job and talk you through the options. See our downlight installation page.

Is it worth doing the whole house at once?

It’s usually the better way. You get matching colour and brightness in every room, and the setup time is shared across the job. Landlords re-lighting an ex-rental between tenants often do it in one go. Fins Up Electrical has done exactly that, swapping out old fittings so the place is brighter, cooler and cheaper to run.

We can check your ceiling, count the fittings and give you a free fixed quote. We’re licensed (91921) and work across the Redcliffe peninsula and Moreton Bay. If you’re redoing other lights at the same time, our lighting installation page covers pendants, wall lights and outdoor lighting.

Want this sorted? Downlight installation from Fins Up.

Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.

Common questions

Do LED downlights work with old halogen transformers?

Sometimes, but often not well. Halogen transformers were built for a higher load, and LED globes on them can flicker, buzz or fail early.

Can insulation go over LED downlights?

Only if the fitting is IC-rated. Check the rating on the fitting, and never cover an old halogen downlight or its transformer.

Will new LED downlights fit the old holes?

Usually. Many LED fittings are made to suit common halogen cut-outs, and larger trims can cover a bigger hole.

Do I need an electrician to replace downlights?

To replace the fitting or transformer, yes. That’s electrical work and in Queensland it must be done by a licensed electrician.

Sources

The service